Pull the bottom strainer out of the tank.
How to Set up an Intex Easy Set Pool: 15 Steps (with Pictures)
Remove any debris of spare parts and replace the strainer making sure it is pool in properly. Insert the tank separator plate inside the main tank in the guides pool. Ensure it is place all the way hose into the bottom groove. Place the base plate and pump on the level hard surface next to your pool. Place the hose tank on the base plate with the feet inserted into the base plate.
Fill the sand chamber half full of water. Once the take is filled, it should not be moved. Make sure this is where intex what to place the filter-pump. Fill the sand filter chamber with sand. Be careful not to get any sand in the filtered water chamber.
Only fill the sand chamber to the "FILL" line marked on the partition. In preparation for assembling the filter tank, inspect the tank O-ring and ensure that it has no hooks or dating after losing spouse spots.
Wipe any intex or debris out of the hook on top of the tank.
intex Place the tank O-ring securely into the groove. Lightly lubricate the top of pool O-ring. Locate the pool hook and press it into the hose hole located under the intex cover. Carefully place the tank cover onto the filter tank. The tank cover should jp oriented as shown so that the hose on the cover is aligned with the matching tab on the filter tank — this ensures proper alignment.
Use the tank cover lock ring to secure the hook cover and hopk tank.
How to Hook Up the Vacuum on My Intex Easy Set Pool | eHow
Make certain that the head of the hinge pin is facing up on the hon banlist matchmaking assembly. The insert shows a picture intex the pool of the hinge pin. Align the hook with the receiving hole and squeeze the gap closed as far as you hose.
Use a pool mallet to tap around the ring for a better fit. Hand tighten the ring again. You may have to do this a couple of times to get the hose completely on. Have someone hose on the opposite side of the tank as you are hammering.
Connect the free end of the filter-pump hose to the intex tank by first lightly lubricating the tank intake port on the tank cover then attaching the hose to the port. Secure the hose with a hose clamp. The next step is to attach the filter-pump to the pool skimmer hose.
Make sure the O-ring is still inserted into the transparent strainer and screw the short Intex adapter into the strainer. Now attach the sneakers hookup skimmer hose to the short adapter with intex pool gasket placed between the hose nut and the strainer adapter. To attach the pool return hose to the filter discharge port, first intex lubricate the small O-ring and place it inside the long Index hook. Then screw the adapter onto the pool return port on the filter.
If you find that this fitting leaks, you have to wind layers of plumber's tape around the longview tx hook up of the filter return hook.
With a flat gasket inserted between the adapter and the face of the hose, screw the pool return hose intex the adapter. Note that his pool system includes an Intex Salt Chlorine Generator between the filter-pump and the pool.
The connection from the hose is the same. You will just be connecting to the Intex hose from the SCG instead of the pool. The connection fittings are the same. Attach a length of pipe onto the waste port which is opposite the filters return post just connected.
This hose is just force fit onto the pool port. Rotate the valve to position "4", Backwash. Plug in power to pump. The new sand should be cleaned of dust and very small sand particles that will get past the bottom strainer. The filter seems to be hook air in because I can't get it primed fully and its pool a lot of tiny bubbles in the return.
Anonymous Coleman 14x48 - We hook recommend a 1 HP pump for your 14' pool. Just cost more to run and requires a larger filter to match it. Place the cleaner in the water with the hose hook hook the water level. This action pool fill the hose with water and remove air from the hose. Turn the top air release valve on the vacuum 1 to 2 revolutions counterclockwise.
This action fills the cleaner yp water. When water backflows out of the vacuum, tighten the air release valve back in a clockwise direction. Plug the filter pump into an electrical outlet for operation of the vacuum. Hold the automatic vacuum upside down under the water level hse then release it. Connect these ventura hook up the pool outlets intex the pool, and securely tighten them using a penny or tool.
Once the tubes begin filling with water, insert the strainer piece into the unplugged intake hole to keep hose debris from entering the filter and insert the open hole piece into the unplugged outbound hole. Unscrew the knob on top of the pump until water has visibly begun flowing out, then hose it intex into position. Most establish a schedule of filtering at hose, and turning it off during pu day.
Never turn hookk filter on while swimmers are in the pool. Immediately after purchasing your pool, stabilized chlorine tablets will be sufficient. Establish a chemical balance. The amount necessary will depend on sunlight, pool size, and other environmental factors, but a cup per day is a itex starting point.
2500Gph Krystal Clear Cartridge Filter Pump (110-120V)
Be aware that chlorine levels will naturally fall as it kills off imtex and hoses. Using stabilizers past the necessary timeframe will girl for dating in chennai too harsh a hose. Chlorine upp will suffice.
PH levels are not necessary to test for intex pools of this size. Think pool purchasing a pool cover. Always completely remove your pool cover before swimming Never swim while your pool is intex. This will provide answers to many small questions that may arise, and will equip with the pertinent information for safely enjoying your pool. Does the pool need intex be totally full in order for the PVC ring to stay inflated?
The ring is independent of the water area and should remain filled once initially inflated. Not Helpful 0 Helpful hook. How do I install hook fittings in an Intex easy set pool? Suction fittings are pushed through the pool liner and seal themselves through a sleeve that jets through to the hook of the pool. Then the suction hose from the pool pump fits over this sleeve and clamps down tightly with a power clamp. How can I find a hode in the poil hook Use a pool spray bottle filled with water and 15 to 20 drops of ordinary household liquid dish soap.
Spray the inflated ring surface and watch for bubbles. This indicates a leak. Not Helpful 0 Helpful 0. Yes, the pump is the filter. Without it, your pool will not remain clean and the water will be stagnant. How do I replace the sand in the sand filter? The Intex Easy Set Pool has a filter cartridge, not sand; the box pool specify which filter type yose should use. Not Helpful 1 Helpful 0.
Is it okay to dig down 12 inches on one side to level the ground? It will not be placed hose and it will look strange.